The VTech LS1350 is a DECT cordless telephone system with digital answering machine, caller ID, call block (up to 100 entries), and expandable design (up to 2 handsets). It features a backlit display, speakerphone, phonebook (100 entries), call log (50 entries), redial, alarm clock, ECO mode, and voicemail indicator. Supports English/Français/Español/Italiano/Nederlands. Below are the key specifications, installation, operation, programming, and troubleshooting instructions.
Unpack the phone and ensure all components are present: telephone base, cordless handset, rechargeable Ni-MH battery pack (2.4V 400mAh), battery compartment cover, base power adapter (6V DC 450mA), telephone line cord, user's manual. Install battery in handset and charge for 16 hours before first use. Place base away from water, heat sources, and interference. Use wall mount if desired.
WARNING! Failure to read and follow all instructions carefully before installing or operating this control could cause personal injury and/or property damage. Save these instructions.
The VTech LS1350 is a DECT cordless phone with digital answering system (up to 99 messages, 15 min recording time). Features include backlit LCD display, speakerphone, adjustable ringer (10 melodies), 100-name phonebook, caller ID log, call block, ECO mode, alarm, quiet mode, voicemail waiting indicator, call screening, and remote access. Supports multiple languages. Handset and base layouts include navigation keys, volume controls, dedicated buttons for mute, redial, find handset, call block.
Applications: Residential cordless telephony; Compatible with DSL/Caller ID; Up to 2 handsets.
CAUTION! To prevent electrical shock/equipment damage, unplug before installation. Use only supplied adapters. If in doubt about wiring, consult qualified electrician.
WARNING! Do not use on circuits exceeding 100-240 VAC; improper use can cause shock/fire. All wiring must conform to local/national electrical codes. Avoid use during storms, near gas leaks, or with pacemakers without consulting doctor. Dispose of batteries per local regulations (WEEE Directive). Install DSL filter if using high-speed internet.
Shut off power if applicable. Remove old phone cover. Label wires before disconnecting. Disconnect wires one at a time; do not let fall into wall. Remove old base from wall.
Plug telephone line cord into base and wall jack (use DSL filter if needed). Plug power adapter into base and unswitched outlet. Install battery in handset (connector first, label up, slide cover). Place handset in base to charge for 16 hours. For wall mount, attach bracket and slide base into place.
Terminal Designations: RJ11 jack for line cord on base; DC jack for power adapter.
Standard Setup: Wall jack to DSL filter (if needed) to base RJ11; Power outlet to adapter to base DC jack.
Wall Mount: Route cords through bracket slots.
CAUTION! All wiring must conform to local/national electrical codes. Do not use switched outlets.
After charging, lift handset and listen for dial tone. Test by dialing a number and adjusting volume. Verify CHARGE light on base.
View via CID; new calls with icon. Dial back with TALK. Save to phonebook via SELECT.
Access menu with MENU/SELECT. Set date/time, program phonebook, configure ringer.
Enter menu via MENU/SELECT. Adjust LCD language, key tone, ringer volume/tone, voicemail number, call block, alarm.
| Setting | Default | Options | Comments |
|---|---|---|---|
| LCD Language | English | English/Français/Italiano/Español/Nederlands | Display text |
| Key Tone | On | On/Off | Beep on key press |
| Ringer Volume | Level 3 | 0-5/Off | Handset ringer |
| Ringer Tone | Tone 1 | 1-10 | Select ring pattern |
| Voicemail Number | None | Custom | Service provider number |
| Call Block | Off | On/Off, up to 100 entries | Block unknown calls |
| ECO Mode | Off | Half/Full/Off | Power saving |
| Alarm | Off | On/Off with time | Wake-up alarm |
| Symptom | Possible Cause | Corrective Action |
|---|---|---|
| Telephone does not work at all | Power off, low battery. | Check power adapter, charge battery; ensure base installed properly. |
| Display shows "No line" or no dial tone | Wiring issue, service problem. | Test line cord on another phone; contact provider; install DSL filter. |
| Display shows "Out of range" or handset not registered | Handset out of range or not registered. | Move closer to base; place in base to register (60 sec). |
| Cannot hear dial tone or make calls | Line cord loose, adapter unplugged. | Check connections; unplug/replug power and line cord. |
| Interference or poor audio | Distance, interference sources. | Move closer; avoid microwaves, install DSL filter. |