The VTech CS6719-2 is a DECT 6.0 cordless telephone system with 2 handsets, featuring caller ID (subscription required), phonebook storage (up to 50 entries), redial (up to 10 last numbers), adjustable ringer and volume (5 levels), voicemail indicator, call blocking (up to 20 entries), backlit keypad, and wall mount capability. It supports English, French, and Spanish and is designed for simple residential use. Below are the key specifications, installation, operation, programming, and troubleshooting instructions.
Unpack the phone and ensure all components are present: 2 handsets, base unit, telephone line cord, AC adapter for base, charger adapter, 2 rechargeable battery packs (Ni-MH 2.4V 400mAh), 2 belt clips, wall mount bracket. For battery installation: Insert the battery pack into each handset compartment (match polarity), then slide the cover into place. Charge new batteries by placing one handset in base cradle and the other in charger for 12 hours before first use. Maximum battery life: Up to 7 hours talk time, 5 days standby. Place base and charger away from water, heat sources, and interference sources like microwaves. If not used for long periods, remove batteries to prevent leakage.
WARNING! Failure to read and follow all instructions carefully before installing or operating this control could cause personal injury and/or property damage. Save these instructions.
The VTech CS6719-2 is a DECT 6.0 cordless phone system with 2 handsets, featuring caller ID (subscription required), phonebook (50 locations), redial (10 last numbers), adjustable volume (5 levels), ringer (OFF/HI/LOW), any key answer, call blocking (20 entries), chain dialing, quiet mode, and ECO mode. Supports basic calling, paging, and voicemail retrieval from service provider. Handset and base layouts include dedicated buttons for /VOL+/ (directory, ringer volume), /VOL-/CID (call log, volume), REDIAL/PAUSE, PROG, SELECT, CHAN/REMOVE, INT (intercom), FLASH, TONE *, #.
Applications: Residential cordless telephony; 2 handsets (expandable to 5).
CAUTION! To prevent electrical shock/equipment damage, unplug before installation. Use only supplied adapters. If in doubt about wiring, consult qualified electrician.
WARNING! Do not use on circuits exceeding 120V AC; improper use can cause shock/fire. All wiring must conform to local/national electrical codes. Avoid use during storms, near gas leaks, or with medical devices (maintain 6-inch distance). Dispose of batteries per local regulations. Install DSL filter if using DSL/high-speed internet.
Plug telephone line cord into base and wall jack (use DSL filter if needed). Plug power adapter into base and unswitched outlet. Plug charger adapter into unswished outlet. Install batteries in handsets (align terminals, snap covers). Place one handset in base and the other in charger to charge for 12 hours. For wall mount, attach bracket to base and wall plate, route cords through slots.
Terminal Designations: Telephone line jack for line cord on base; Power jack for adapter on base and charger.
Standard Setup: Wall jack to DSL filter (if needed) to base line jack; Power outlet to adapter to base/charger power jack.
Wall Mount: Insert wall bracket tabs into base grooves, mount on wall studs.
CAUTION! All wiring must conform to local/national electrical codes. Do not use switched outlets.
After charging, lift handset and listen for dial tone (wait 1-2 seconds). Test by dialing a number and adjusting volume. Verify CHARGE light on base and charger.
Redial: Press REDIAL/PAUSE, press PHONE to dial.
Access phonebook with /VOL+/ (directory).
Caller ID: /VOL-/CID > Scroll > PHONE to dial > SELECT > PROGRAM to save to phonebook.
Changes activate immediately.
Adjust via PROG: Date/Time, Ringer, Dial Mode, Home Area Code, Language.
| Setting | Default | Options | Comments |
|---|---|---|---|
| Ringer Tone | Tone 1 | 10 tones | PROG > RINGER > Ringer tone > Sample > SELECT |
| Ringer Volume | Medium | OFF/HI/LOW | Hold VOL during idle or PROG > RINGER > Ringer volume |
| Handset Volume | Level 3 | 5 levels | Adjust during call |
| Language | English | English/French/Spanish | PROG > LANGUAGE |
| Dial Mode | Tone | Tone/Pulse | PROG > DIAL MODE |
| Quiet Mode | Off | 1-12 hours | Hold # > Enter time > SELECT (mutes tones except paging) |
| Voicemail Number | None | Up to 30 digits | PROG > VOICEMAIL # > Enter number > SELECT (hold # to retrieve) |
Set Time/Date: PROG > DATE/TIME > Enter MM/DD/YY, HH:MM > SELECT.
Clear Voicemail Indicators: PROG > CLR VOICEMAIL > SELECT.
| Symptom | Possible Cause | Corrective Action |
|---|---|---|
| Telephone does not work at all | No power, low battery. | Check adapters, charge 12 hours; unplug/replug power (15 sec); test with another phone. |
| No dial tone | Wiring issue. | Check line cord; test jack; contact provider for wiring/DSL/VoIP issues. |
| Poor audio quality | Out of range, interference. | Move closer; press CHAN; avoid electronics; install DSL filter; centralize base. |
| Cannot store numbers | Memory full (20 max). | Delete entries. |
| Handset does not ring | Ringer off. | Set ringer ON; check plugs; reinsert battery. |
| Voicemail indicators persist | Service provider messages. | Use CLR VOICEMAIL feature (does not delete messages). |
Handset Registration: Base: Press MENU > Register HS > Place handset in cradle.