The VTech CS6229-2 is a DECT 6.0 cordless telephone system with digital answering machine, caller ID, and expandable design (up to 5 handsets). It features a backlit display, speakerphone, phonebook (50 entries), call log (50 entries), redial (5 entries), quiet mode, voicemail indicator, and intercom. Supports English/Français/Español. Below are the key specifications, installation, operation, programming, and troubleshooting instructions.
Unpack the phone and ensure all components are present: quick start guide, handset(s) (2 for CS6229-2), telephone base, charger(s) and adapter(s) (1 for CS6229-2), battery compartment cover(s), battery(ies) (2 for CS6229-2), telephone base power adapter, telephone line cord, user's manual, wall bracket. Install the telephone base and charger(s) by plugging the power adapter into an electrical outlet not controlled by a wall switch and the telephone line cord into the wall jack. If using DSL, install a DSL filter between the line cord and wall jack. For battery installation: remove the battery compartment cover, plug the battery into the handset compartment matching color-coded labels with "THIS SIDE UP" facing up, replace the cover until it clicks, and place the handset in the base or charger. Charge for at least 16 hours before first use; the CHARGE light is on during charging. Battery indicators: blank screen (no charge, charge at least 10 minutes), PLACE IN CHARGER flashing (very low, charge about 4 minutes), LOW BATTERY flashing with beep (short use possible, charge about 1 hour), HANDSET X (fully charged).
WARNING! Failure to read and follow all instructions carefully before installing or operating this control could cause personal injury and/or property damage. Save these instructions.
The VTech CS6229-2 is a cordless DECT 6.0 phone with digital answering system (up to 99 messages, 22 minutes recording time). Features include backlit display, speakerphone, adjustable ringer, 50-name phonebook, 50-name caller ID log, 5-number redial, intercom, chain dialing, multiple handset use, remote access, and voicemail indicator. Supports English, French, Spanish. Handset layout: /FLASH (make/answer call), (speakerphone), VOL (volume), (directory/up), CID (call log/down), MENU/SELECT (menu/save), OFF/CLEAR (end call/silence ringer), # (dialing options), MUTE/REMOVE (mute/delete), INT (intercom), REDIAL/PAUSE (redial/pause), dialing keys, CHARGE light. Base layout: FIND HANDSET (page handsets), /REPEAT (repeat message), /SKIP (skip message), X/DELETE (delete message), ANS ON/OFF (turn answering system on/off), /PLAY/STOP (play/stop messages), VOL (volume/ringer), IN USE light, VOICEMAIL light, message window.
Applications: Residential cordless telephony; Compatible with DSL/Caller ID; Up to 5 handsets.
CAUTION! To prevent electrical shock/equipment damage, unplug before installation. Use only supplied adapters. If in doubt about wiring, consult qualified electrician.
WARNING! Do not use on circuits exceeding 120 VAC; improper use can cause shock/fire. All wiring must conform to local/national electrical codes. Avoid use during storms, near gas leaks, or with pacemakers without consulting doctor. Dispose of batteries per local regulations. Install DSL filter if using high-speed internet. Calls transmitted by radio waves may be intercepted (not as private as corded); requires electrical outlet (calls impossible if unplugged); potential TV/VCR interference; dispose of batteries via RBRC program.
Shut off power if applicable. Remove old phone cover. Label wires before disconnecting. Disconnect wires one at a time; do not let fall into wall. Remove old base from wall.
Plug telephone line cord into base and wall jack (use DSL filter if needed). Plug power adapter into base and unswitched outlet. Install batteries in handsets (connector first, label up, slide cover). Place handsets in base/charger to charge for 16 hours. For wall mount, insert extended tabs (B) of wall bracket into base slots (B), push down to click; route line cord (or DSL filter) through bracket hole, power cord out bottom; plug line into wall jack, power into outlet; align bracket holes with wall plate, slide down to lock. Register additional handsets via FIND HANDSET on base (hold 4 seconds).
Terminal Designations: RJ11 jack for line cord on base; DC jack for power adapter.
Standard Setup: Wall jack to DSL filter (if needed) to base RJ11; Power outlet to adapter to base DC jack.
Wall Mount: Route cords through bracket holes.
CAUTION! All wiring must conform to local/national electrical codes. Do not use switched outlets.
After charging, lift handset and listen for dial tone (if no tone, ensure line cord plugged firmly, power adapter secure, no wall switch off; unplug/replug power, wait 15 seconds, allow 1 minute sync; test with another phone at wall jack). Test by dialing a number and adjusting volume. Verify CHARGE light on base. Test paging: Press FIND HANDSET on base (handsets ring with **PAGING**).
View via CID (shows XX MISSED CALL(S) for unreviewed; browse with / , NEW marks new). Dial back: Browse, press # for format (e.g., 800-595-9511), press /FLASH to dial. Save to phonebook: Browse, press MENU/SELECT > EDIT NUMBER > MENU/SELECT > ENTER NAME > MENU/SELECT > SAVE.
Access menu with MENU/SELECT. Set date/time, program phonebook, configure ringer.
Enter menu via MENU/SELECT. Adjust LCD language, key tone, ringer volume/tone, voicemail number, call block, quiet mode.
| Setting | Default | Options | Comments |
|---|---|---|---|
| LCD Language | English | English/Français/Español | Menu > Settings > Language |
| Key Tone | On | On/Off | Menu > Settings > Key tone |
| Ringer Volume | Level 3 | Off/1-5 | Menu > Ringers > Ringer volume |
| Ringer Tone | Tone 1 | 1-10 | Menu > Ringers > Ringer tone |
| Voicemail Number | None | Custom | Menu > Settings > Voicemail # |
| Call Block | Off | On/Off | Menu > Call block |
| Quiet Mode | Off | On/Off | Set ringer to off |
| Symptom | Possible Cause | Corrective Action |
|---|---|---|
| Telephone does not work at all | Power off, low battery. | Check power adapter, charge battery; ensure base installed properly. |
| Display shows "No line" or no dial tone | Wiring issue, service problem. | Test line cord on another phone; contact provider; install DSL filter. |
| Handset not registered | Not registered. | Place in base to auto-register (60 sec). |
| Handset does not ring | Ringer off, volume low. | Set ringer volume via menu; check connections. |