The VTech CS5119 is a DECT 6.0 cordless telephone system with handset, telephone base, and optional chargers. It supports intercom, caller ID, phonebook (up to 50 entries), redial (10 entries), call block (20 entries), quiet mode, and ECO mode for power conservation. Compatible with DSL/Caller ID services. Below are the key specifications, installation, operation, programming, and troubleshooting instructions.
Unpack the phone and ensure all components are present: handset, telephone base, power adapter, telephone line cord, battery pack, battery compartment cover, belt clip, wall mounting bracket (if included). Install battery in handset and charge for 12 hours before first use. Place base away from water, heat sources, and interference. Use screwdriver for wall mounting if desired.
WARNING! Failure to read and follow all instructions carefully before installing or operating this control could cause personal injury and/or property damage. Save these instructions.
The VTech CS5119 is a DECT 6.0 cordless phone with crystal clear sound, expandable up to 5 handsets. Features include backlit display, speakerphone, adjustable ringer, phonebook, caller ID log (30 entries), redial, call block, quiet mode, and voicemail indicator. Handset and base layouts include navigation keys, volume controls, mute, and dedicated buttons for INT, CID, REDIAL.
Applications: Residential cordless telephony; Compatible with DSL/Caller ID; Up to 5 handsets.
CAUTION! To prevent electrical shock/equipment damage, unplug before installation. Use only supplied adapters. If in doubt about wiring, consult qualified electrician.
WARNING! Do not use on circuits exceeding 120 VAC; improper use can cause shock/fire. All wiring must conform to local/national electrical codes. Avoid use during storms, near gas leaks, or with pacemakers without consulting doctor. Dispose of batteries per local regulations. Install DSL filter if using high-speed internet.
Shut off power if applicable. Remove old phone cover. Label wires before disconnecting. Disconnect wires one at a time; do not let fall into wall. Remove old base from wall.
Connect telephone line cord to base and wall jack (use DSL filter if needed). Connect power adapter to base and unswitched outlet. Install battery in handset (connector first, label up, slide cover). Place handset in base to charge for 12 hours. For wall mount, attach bracket and slide base into place.
Terminal Designations: RJ11 jack for line cord on base; DC jack for power adapter.
Standard Setup: Wall jack to DSL filter (if needed) to base RJ11; Power outlet to adapter to base DC jack.
Wall Mount: Route cords through bracket slots.
CAUTION! All wiring must conform to local/national electrical codes. Do not use switched outlets.
After charging, lift handset and listen for dial tone. Test by dialing a number and adjusting volume. Verify CHARGE light on base.
The system includes an answering machine. Refer to full manual for setup: Record announcement via menu, set rings (2-6/Toll saver), remote access code. Play messages with PLAY/STOP on base.
View via CID; new calls with icon. Dial back with talk/flash. Save to phonebook via SELECT.
Access menu with MENU/SELECT. Set date/time, program phonebook, configure ringer.
Enter menu via MENU/SELECT. Adjust LCD language, key tone, ringer volume/tone, voicemail number, call block, quiet mode.
| Setting | Default | Options | Comments |
|---|---|---|---|
| LCD Language | English | English/Français/Español | Display text |
| Key Tone | On | On/Off | Beep on key press |
| Ringer Volume | Level 3 | 0-5/Off | Handset ringer |
| Ringer Tone | Tone 1 | 1-5 | Select ring pattern |
| Voicemail Number | None | Custom | Service provider number |
| Call Block Unknown | Off | On/Off | Block no-number calls |
| Quiet Mode | Off | On/Off with duration | Silence ringer/alarms |
| Symptom | Possible Cause | Corrective Action |
|---|---|---|
| Telephone does not work at all | Power off, low battery. | Check power adapter, charge battery; ensure base installed properly. |
| Display shows "No line" or no dial tone | Wiring issue, service problem. | Test line cord on another phone; contact provider. |
| Display shows "To register HS… and …see manual" | Handset not registered. | Place handset in base to auto-register (60 sec). |
| Accidentally set LCD language to Spanish or French | Menu navigation error. | Press MENU, enter 364# to reset to English. |