VTech CS5119 Cordless Telephone User Manual

The VTech CS5119 is a 5.8 GHz cordless telephone with digital answering system, featuring caller ID (subscription required), phonebook storage (up to 50 entries), redial, adjustable ringer and volume, voicemail indicator, backlit keypad, and wall mount capability. It supports English and is designed for simple residential use. Below are the key specifications, installation, operation, programming, and troubleshooting instructions.

Preparations

Unpack the phone and ensure all components are present: handset, base unit with answering system, telephone line cord, AC adapter, rechargeable battery pack (Ni-MH 2.4V 500mAh), belt clip, wall mount bracket. For battery replacement: Slide open battery door, insert pack with correct polarity, close door. Charge new battery by placing handset in base cradle for 12 hours before first use. Maximum battery life: Up to 7 hours talk time, 7 days standby. Place base away from water, heat sources, and interference sources like microwaves.

WARNING! Failure to read and follow all instructions carefully before installing or operating this control could cause personal injury and/or property damage. Save these instructions.

Description

The VTech CS5119 is a 5.8 GHz cordless phone with built-in digital answering machine (up to 25 minutes recording time), including caller ID (subscription required), phonebook (50 locations), redial (last 5 numbers), adjustable volume (5 levels), ringer (5 melodies/OFF), and any key answer. Supports basic calling, paging, message playback, and remote access. Handset and base layouts include dedicated buttons for CID/>, REDIAL/PAUSE, VOL +/-, MUTE, PLAY/STOP, SKIP, REPEAT.

Applications: Residential cordless telephony with answering system; Single handset.

Precautions

CAUTION! To prevent electrical shock/equipment damage, unplug before installation. Use only supplied adapters. If in doubt about wiring, consult qualified electrician.

WARNING! Do not use on circuits exceeding 120V AC; improper use can cause shock/fire. All wiring must conform to local/national electrical codes. Avoid use during storms, near gas leaks, or with medical devices (maintain 6-inch distance). Dispose of batteries per local regulations. Install DSL filter if using DSL/high-speed internet.

• WARNING! Use only the power adapters provided with this product: 6V DC 400mA.

Specifications

• Electrical: Frequency: 5.8 GHz; Channels: Auto-select; Power: 120V AC, 60Hz; Adapter: 6V DC @ 400mA.
• Batteries: Ni-MH rechargeable, 2.4V 500mAh; Charge time: 12 hours; Talk time: Up to 7 hours; Standby: 7 days.
• Range: Up to 50 feet indoors, 300 feet outdoors; Varies by location.
• Operating Ambient: 32°F to 104°F (0°C to 40°C); Humidity: Up to 95% non-condensing.
• Dimensions: Handset: 6.65 x 2.04 x 1.14 inches; Base: 5.04 x 3.66 x 2.36 inches.
• Other: Memory Dialing: 50 entries; Answering System: 25 min recording; Languages: English.

Installation

Plug telephone line cord into base and wall jack (use DSL filter if needed). Plug power adapter into base and unswitched outlet. Install battery in handset (align terminals, snap cover). Place handset in base to charge for 12 hours. For wall mount, attach bracket to base and wall plate, route cords through designated paths. Set up answering system: Press SKIP to set day/time.

Connection Diagrams

Terminal Designations: TEL LINE jack for line cord on base; DC 6V jack for power adapter.

Standard Setup: Wall jack to DSL filter (if needed) to base TEL LINE; Power outlet to adapter to base DC jack.

Wall Mount: Secure bracket to wall plate, hang base on bracket hooks.

CAUTION! All wiring must conform to local/national electrical codes. Do not use switched outlets. The equipment should only be used with the power adapter provided.

Check Operation

After charging, press TALK and listen for dial tone. Test by dialing a known number and adjusting volume. Verify IN USE/CHARGE light on base illuminates when handset is in cradle. Test answering system by calling from another phone.

Basic Calling

1. Enter number (up to 32 digits), press TALK to dial.
2. To answer: Press TALK or any dial pad key (if enabled).
3. Adjust volume with VOL +/- during call.
4. End call: Press OFF or place handset in base.

Flash/Call Waiting: Press FLASH during call. Redial: Press REDIAL/PAUSE to cycle through last 5 numbers, press TALK to dial.

Operating Features

• Home Screen: Backlit LCD shows battery status, signal strength, time/day.
• Key Features: Caller ID memory (up to 50 entries), phonebook dialing, chain dialing, temporary silence (press # to mute ringer for current call), paging from base.
• Paging: Press PAGE on base (handset beeps; press OFF or place in base to stop).
• Answering System: Auto attendant, remote access via PIN (default 000), message counter on base.

Programming

Access phonebook via dedicated key or menu.

1. Store Numbers: Press PHONEBOOK > STORE > Enter number (up to 32 digits) > STORE > Enter name (up to 15 letters) > STORE > Select location (1-50) > STORE.
2. Dial Stored Number: Press PHONEBOOK > Scroll or enter location > Press TALK.
3. Edit: PHONEBOOK > Scroll to entry > EDIT > Modify number/name > STORE.
4. Delete: PHONEBOOK > Scroll to entry > DELETE > Confirm with STORE. Or delete all via menu.

Caller ID: Press CID/> to review list, dial with TALK, store to phonebook.

Changes activate immediately.

Configuration

Adjust via handset menu: Ringer type/volume, LCD language, dial mode, any key answer, area code entry, answering system settings (announcement, ring delay).

Set Time/Date: Base: Press SKIP repeatedly during setup or Menu > Set Date/Time > Enter MM/DD/YY and HH:MM > AM/PM if 12-hour.

Remote Access PIN: Default 000; Change via menu.

Troubleshooting

Message Playback: Base: Press PLAY/STOP. Handset: Menu > Play Messages.