The VTech CS5119-2 is a 5.8 GHz cordless telephone system with 2 handsets and digital answering system, featuring caller ID (subscription required), phonebook storage (up to 50 entries), redial, adjustable ringer and volume, voicemail indicator, backlit keypad, and wall mount capability. It supports English and is designed for simple residential use. Below are the key specifications, installation, operation, programming, and troubleshooting instructions.
Unpack the phone and ensure all components are present: 2 handsets, base unit with answering system, telephone line cord, AC adapter for base, charger adapter, 2 rechargeable battery packs (Ni-MH 2.4V 500mAh), 2 belt clips, wall mount bracket. For battery replacement: Slide open battery door on each handset, insert pack with correct polarity, close door. Charge new batteries by placing one handset in base cradle and the other in charger for 12 hours before first use. Maximum battery life: Up to 7 hours talk time, 7 days standby. Place base and charger away from water, heat sources, and interference sources like microwaves.
WARNING! Failure to read and follow all instructions carefully before installing or operating this control could cause personal injury and/or property damage. Save these instructions.
The VTech CS5119-2 is a 5.8 GHz cordless phone system with 2 handsets and built-in digital answering machine (up to 25 minutes recording time), including caller ID (subscription required), phonebook (50 locations), redial (last 5 numbers), adjustable volume (5 levels), ringer (5 melodies/OFF), any key answer, and intercom. Supports basic calling, paging, message playback, and remote access. Handset and base layouts include dedicated buttons for CID/>, REDIAL/PAUSE, VOL +/-, MUTE, INT, PLAY/STOP, SKIP, REPEAT.
Applications: Residential cordless telephony with answering system; 2 handsets.
CAUTION! To prevent electrical shock/equipment damage, unplug before installation. Use only supplied adapters. If in doubt about wiring, consult qualified electrician.
WARNING! Do not use on circuits exceeding 120V AC; improper use can cause shock/fire. All wiring must conform to local/national electrical codes. Avoid use during storms, near gas leaks, or with medical devices (maintain 6-inch distance). Dispose of batteries per local regulations. Install DSL filter if using DSL/high-speed internet.
Plug telephone line cord into base and wall jack (use DSL filter if needed). Plug power adapter into base and unswitched outlet. Plug charger adapter into unswitched outlet. Install batteries in handsets (align terminals, snap covers). Place one handset in base and the other in charger to charge for 12 hours. For wall mount, attach bracket to base and wall plate, route cords through designated paths. Set up answering system: Press SKIP to set day/time.
Terminal Designations: TEL LINE jack for line cord on base; DC 6V jack for power adapter on base and charger.
Standard Setup: Wall jack to DSL filter (if needed) to base TEL LINE; Power outlet to adapter to base DC jack; Separate outlet to charger adapter.
Wall Mount: Secure bracket to wall plate, hang base on bracket hooks.
CAUTION! All wiring must conform to local/national electrical codes. Do not use switched outlets. The equipment should only be used with the power adapter provided.
After charging, press TALK on a handset and listen for dial tone. Test by dialing a known number and adjusting volume. Verify IN USE/CHARGE light on base and charger illuminate when handsets are in cradles. Test answering system by calling from another phone.
Flash/Call Waiting: Press FLASH during call. Redial: Press REDIAL/PAUSE to cycle through last 5 numbers, press TALK to dial. Intercom: Press INT on one handset to call the other.
Access phonebook via dedicated key or menu.
Caller ID: Press CID/> to review list, dial with TALK, store to phonebook.
Changes activate immediately.
Adjust via handset menu: Ringer type/volume, LCD language, dial mode, any key answer, area code entry, answering system settings (announcement, ring delay).
| Setting | Default | Options | Comments |
|---|---|---|---|
| Ringer Type | Melody 1 | 5 melodies | Menu > Ringer Setup |
| Ringer Volume | Level 3 | 5 levels / OFF | Menu > Ringer Setup |
| Handset Volume | Level 3 | 5 levels | Adjust during call |
| LCD Language | English | English | Limited options |
| Dial Mode | Tone | Tone/Pulse | Menu > Dial Mode |
| Any Key Answer | On | On/Off | Menu > Answering Setup |
| Announcement | Pre-recorded | Record new | Base: RECORD > 1 > Speak > PLAY/STOP |
| Ring Delay | 2 rings | 2-7 rings | Menu > Answering Setup > Rings to Answer |
Set Time/Date: Base: Press SKIP repeatedly during setup or Menu > Set Date/Time > Enter MM/DD/YY and HH:MM > AM/PM if 12-hour.
Remote Access PIN: Default 000; Change via menu.
| Symptom | Possible Cause | Corrective Action |
|---|---|---|
| Telephone does not work at all | Power off, low battery. | Check power adapter connections, charge batteries 12 hours; ensure line cord plugged in. |
| No dial tone | Wiring issue, service outage. | Test with another phone; contact service provider; verify DSL filter. |
| Poor audio quality or interference | Out of range, electrical interference. | Move closer to base; avoid microwave ovens, wireless devices; fully charge batteries. |
| Cannot store a phonebook entry | Memory full. | Delete unused entries; maximum 50. |
| Handset does not ring | Ringer off, low volume, not registered. | Check ringer settings; re-register handset to base. |
| Answering system not recording | Full memory, off. | Delete messages; turn on ANS ON/OFF switch. |
Message Playback: Base: Press PLAY/STOP. Handset: Menu > Play Messages.
Handset Registration: Base: Press MENU > Register HS > Place handset in cradle.