VTech CS5111 Cordless Telephone User Manual

The VTech CS5111 is a 5.8GHz/900MHz cordless telephone with features including caller ID (subscription required), directory storage (20 entries), speed dial (9 locations), call log (50 entries), redial, adjustable ringer and volume, voicemail waiting indicator (service provider), backlit display, and wall mount capability. It supports English, Spanish, and French and is designed for simple residential use. Below are the key specifications, installation, operation, programming, and troubleshooting instructions.

Preparations

Unpack the phone and ensure all components are present: handset, telephone line cord, power adapter for telephone base, battery pack, handset charger (for CS5113 model), battery compartment cover, wall bracket for telephone base (for CS5113 model). Save sales receipt and packaging for warranty. For battery installation: Insert the battery pack into the handset compartment, then slide the cover into place. Charge new battery by placing handset in base cradle for at least 16 hours before first use. Maximum battery life: Up to 5 hours talk time, 6 days standby. Place base away from water, heat sources, and interference.

WARNING! Failure to read and follow all instructions carefully before installing or operating this control could cause personal injury and/or property damage. Save these instructions.

Description

The VTech CS5111 is a 5.8GHz/900MHz cordless phone with basic features including caller ID (subscription required), directory (20 locations), speed dial (9 locations), redial (5 last numbers), adjustable volume (5 levels), ringer (OFF to High), and any key answer. Supports basic calling, paging, and voicemail indicator. Handset and base layouts include dedicated buttons for /VOL+/ (directory, ringer volume), /VOL-/CID (call log, volume), REDIAL/PAUSE, PROG, SELECT, CHAN/REMOVE, INT (intercom), FLASH, TONE, OFF.

Applications: Residential cordless telephony; Expandable to 3 handsets (CS5113 model).

Precautions

CAUTION! To prevent electrical shock/equipment damage, unplug before installation. Use only supplied adapters. If in doubt about wiring, consult qualified electrician.

WARNING! Do not use on circuits exceeding 120V AC; improper use can cause shock/fire. All wiring must conform to local/national electrical codes. Avoid use during storms, near gas leaks, or with medical devices (maintain 6-inch distance). Dispose of batteries per local regulations. Install DSL filter if using DSL/high-speed internet.

• WARNING! Use only the power adapters provided with this product: 9V DC @ 400mA.

Specifications

• Electrical: Frequency: 5.8GHz/900MHz; Channels: Auto-select; Power: 120V AC, 60Hz; Adapter: 9V DC @ 400mA.
• Batteries: Ni-MH rechargeable, 2.4V 400mAh; Charge time: 16 hours; Talk time: Up to 5 hours; Standby: 6 days.
• Range: Up to 50 feet indoors, 300 feet outdoors; Varies by location.
• Operating Ambient: 32°F to 122°F (0°C to 50°C); Humidity: Up to 95% non-condensing.
• Dimensions: Handset: 7.32 x 2.01 x 1.57 inches; Base: 5.83 x 3.90 x 2.60 inches.
• Other: Directory: 20 entries; Speed Dial: 9; Call Log: 50; Languages: English/Spanish/French.

Installation

Plug telephone line cord into base and wall jack (use DSL filter if needed). Plug power adapter into base and unswitched outlet. Install battery in handset (align terminals, snap cover). Place handset in base to charge for 16 hours. For wall mount (CS5113), attach bracket to base and wall plate, route cords through slots.

Connection Diagrams

Terminal Designations: Telephone line jack for line cord on base; Power jack for adapter.

Standard Setup: Wall jack to DSL filter (if needed) to base line jack; Power outlet to adapter to base power jack.

Wall Mount: Insert wall bracket tabs into base grooves, mount on wall studs.

CAUTION! All wiring must conform to local/national electrical codes. Do not use switched outlets.

Check Operation

After charging, lift handset and listen for dial tone (wait 1-2 seconds). Test by dialing a number and adjusting volume. Verify CHARGE light on base.

Basic Calling

1. Press PHONE, enter number.
2. To answer: Press any dial pad key (except /VOL-/CID, /VOL+/, OFF).
3. Adjust volume with VOL +/-.
4. End call: Press OFF or place in base.

Redial: Press REDIAL/PAUSE, press PHONE to dial.

Operating Features

• Home Screen: LCD shows battery status, signal strength, caller ID info.
• Key Features: Caller ID memory (50 entries), directory dialing, speed dial, chain dialing, temporary ringer silence, paging from base, intercom (CS5113).
• Paging: Press FIND HANDSET on base (handset beeps 60 seconds).
• Voicemail Indicator: VOICEMAIL light flashes for service provider messages.

Programming

Access directory with PROG.

1. Store Numbers: Press PROG > STORE > Enter number (up to 24 digits) > SELECT > Enter name (up to 14 chars) > SELECT.
2. Dial Stored Number: Scroll to entry > Press PHONE.
3. Edit: Scroll to entry > SELECT > EDIT > Modify > SELECT.
4. Delete: Scroll to entry > SELECT > DELETE > SELECT.

Speed Dial: Press and hold 1-9 > Enter number > SELECT > Name > SELECT.

Changes activate immediately.

Configuration

Adjust via PROG: Date/Time, Ringer Volume, Dial Mode, Home Area Code, Language.

Set Time/Date: PROG > DATE/TIME > Enter MM/DD/YY, HH:MM > SELECT.

Troubleshooting