VTech CS5111-2 Cordless Telephone User Manual

The VTech CS5111-2 is a 5.8GHz/900MHz cordless telephone system with 2 handsets, featuring caller ID (subscription required), directory storage (20 entries), speed dial (9 locations), call log (50 entries), redial, adjustable ringer and volume, voicemail waiting indicator (service provider), backlit display, and wall mount capability. It supports English, Spanish, and French and is designed for simple residential use. Below are the key specifications, installation, operation, programming, and troubleshooting instructions.

Preparations

Unpack the phone and ensure all components are present: 2 handsets, telephone line cord, power adapter for telephone base, charger adapter, 2 battery packs, 2 battery compartment covers, wall bracket for telephone base. Save sales receipt and packaging for warranty. For battery installation: Insert the battery pack into each handset compartment, then slide the cover into place. Charge new batteries by placing one handset in base cradle and the other in charger for at least 16 hours before first use. Maximum battery life: Up to 5 hours talk time, 6 days standby. Place base and charger away from water, heat sources, and interference.

WARNING! Failure to read and follow all instructions carefully before installing or operating this control could cause personal injury and/or property damage. Save these instructions.

Description

The VTech CS5111-2 is a 5.8GHz/900MHz cordless phone system with 2 handsets and basic features including caller ID (subscription required), directory (20 locations), speed dial (9 locations), redial (5 last numbers), adjustable volume (5 levels), ringer (OFF to High), and any key answer. Supports basic calling, paging, voicemail indicator, and intercom. Handset and base layouts include dedicated buttons for /VOL+/ (directory, ringer volume), /VOL-/CID (call log, volume), REDIAL/PAUSE, PROG, SELECT, CHAN/REMOVE, INT (intercom), FLASH, TONE, OFF.

Applications: Residential cordless telephony; 2 handsets.

Precautions

CAUTION! To prevent electrical shock/equipment damage, unplug before installation. Use only supplied adapters. If in doubt about wiring, consult qualified electrician.

WARNING! Do not use on circuits exceeding 120V AC; improper use can cause shock/fire. All wiring must conform to local/national electrical codes. Avoid use during storms, near gas leaks, or with medical devices (maintain 6-inch distance). Dispose of batteries per local regulations. Install DSL filter if using DSL/high-speed internet.

• WARNING! Use only the power adapters provided with this product: 9V DC @ 400mA for base, 9V DC @ 300mA for charger.

Specifications

• Electrical: Frequency: 5.8GHz/900MHz; Channels: Auto-select; Power: 120V AC, 60Hz; Adapter: 9V DC @ 400mA (base), 300mA (charger).
• Batteries: Ni-MH rechargeable, 2.4V 400mAh (2 packs); Charge time: 16 hours; Talk time: Up to 5 hours; Standby: 6 days.
• Range: Up to 50 feet indoors, 300 feet outdoors; Varies by location.
• Operating Ambient: 32°F to 122°F (0°C to 50°C); Humidity: Up to 95% non-condensing.
• Dimensions: Handset: 7.32 x 2.01 x 1.57 inches; Base: 5.83 x 3.90 x 2.60 inches; Charger: Compact.
• Other: Directory: 20 entries; Speed Dial: 9; Call Log: 50; Languages: English/Spanish/French.

Installation

Plug telephone line cord into base and wall jack (use DSL filter if needed). Plug power adapter into base and unswitched outlet. Plug charger adapter into unswitched outlet. Install batteries in handsets (align terminals, snap covers). Place one handset in base and the other in charger to charge for 16 hours. For wall mount, attach bracket to base and wall plate, route cords through slots.

Connection Diagrams

Terminal Designations: Telephone line jack for line cord on base; Power jack for adapter on base and charger.

Standard Setup: Wall jack to DSL filter (if needed) to base line jack; Power outlet to adapter to base power jack; Separate outlet to charger adapter.

Wall Mount: Insert wall bracket tabs into base grooves, mount on wall studs.

CAUTION! All wiring must conform to local/national electrical codes. Do not use switched outlets.

Check Operation

After charging, lift a handset and listen for dial tone (wait 1-2 seconds). Test by dialing a number and adjusting volume. Verify CHARGE light on base and charger.

Basic Calling

1. Press PHONE, enter number.
2. To answer: Press any dial pad key (except /VOL-/CID, /VOL+/, OFF).
3. Adjust volume with VOL +/-.
4. End call: Press OFF or place in base/charger.

Redial: Press REDIAL/PAUSE, press PHONE to dial. Intercom: Press INT on one handset to call the other.

Operating Features

• Home Screen: LCD shows battery status, signal strength, caller ID info.
• Key Features: Caller ID memory (50 entries), directory dialing, speed dial, chain dialing, temporary ringer silence, paging from base, intercom between handsets.
• Paging: Press FIND HANDSET on base (handsets beep 60 seconds).
• Voicemail Indicator: VOICEMAIL light flashes for service provider messages.

Programming

Access directory with PROG.

1. Store Numbers: Press PROG > STORE > Enter number (up to 24 digits) > SELECT > Enter name (up to 14 chars) > SELECT.
2. Dial Stored Number: Scroll to entry > Press PHONE.
3. Edit: Scroll to entry > SELECT > EDIT > Modify > SELECT.
4. Delete: Scroll to entry > SELECT > DELETE > SELECT.

Speed Dial: Press and hold 1-9 > Enter number > SELECT > Name > SELECT.

Changes activate immediately.

Configuration

Adjust via PROG: Date/Time, Ringer Volume, Dial Mode, Home Area Code, Language.

Set Time/Date: PROG > DATE/TIME > Enter MM/DD/YY, HH:MM > SELECT.

Troubleshooting

Handset Registration: Base: Press MENU > Register HS > Place handset in cradle.