The VTech C4500 is a SIP cordless 2-line accessory handset designed for use with VTech SIP Contemporary Series 2-line bases, such as the S2410. It provides cordless mobility, charging functionality via compatible charging bases like the C4300, and hospitality features for guest rooms. It supports DECT 6.0 technology for registration and operation. It is part of a system that includes compatible bases and charging bases with power adapters and mounting brackets. Below are the key specifications, installation, operation, programming, and troubleshooting instructions for the C4500 handset.
Verify all parts are included: Cordless handset, rechargeable NiMH battery pack (BT264392/BT266342, 2.4V), screw (BY 1021), battery compartment cover. Install and charge handset battery before use. Ensure handset is registered to a compatible 2-line SIP base (e.g., S2410) before placing into charging base. Keep handset in the telephone base or charging base when not in use for optimal performance. Avoid placing near communication devices, heat sources, noise, dust, moisture, low temperatures, or vibrations.
CAUTIONS: Use only the supplied power adapter for charging base. To order replacements, call 1-888-907-2007. This product should be installed by a qualified technician. Save these instructions.
Handset Battery Installation: Gently lift the handset cover. Do not detach the speaker wires. Plug the battery connector securely into the socket inside the handset battery compartment. Place the battery with the label THIS SIDE UP facing up and the wires inside the battery compartment. Align all tabs on the handset cover against the corresponding grooves on the handset, then firmly push downward until all tabs lock. Secure with screw.
The C4500 is a SIP cordless 2-line accessory handset designed for use with VTech SIP Contemporary Series 2-line bases and the C4300 charging base. Handset layout: LINE 1 Key, CONF Key, LINE 2 Key, HOLD Key, OFF Key, FLASH Key, SPEAKER Key, REDIAL Key, LOW BATTERY LED, MUTE Key, MESSAGE WAITING LED, +/VOLUME/- Keys. The C4300 charging base includes: CHARGE LED. Supports battery charging, automatic handset registration/deregistration via DECT. Unique hospitality features: Programmable speed dial keys for guest services, message waiting LED (steady/periodic high/low voltage pulse, reverse polarity, FSK, Siemens/Panasonic), energy-saving modes. Nominal effective range: Varies by environment; crystal-controlled PLL synthesizer with 5 channels, transmit frequency 1921.536-1928.448 MHz. Designed for guest room cordless mobility in 2-line SIP setups.
Applications: Hospitality SIP telephony; cordless 2-line accessory handset for hotel desk/wall setups.
CAUTION! To prevent electrical shock or equipment damage, unplug before installation. Use only supplied Cat-5 network cable.
WARNING! Follow safety precautions to reduce risk of fire, electric shock, or injury. Do not use near water; avoid rough handling. Do not open casing. Maintain 6-inch distance from medical devices like pacemakers. Wiring conforms to local codes. Avoid storms or gas leaks. Install by qualified technician only; connect only to host equipment. Use only specified adapter and battery (BT264392/BT266342, 2.4V Ni-MH); incorrect types risk explosion. Dispose batteries per local codes, not in fire. Keep metallic objects away from handset. Mount at less than 2 meters height. Operate in 0°C - 50°C, 5%-95% humidity non-condensing.
For C4300 Charging Base: Choose area near outlet. Plug Cat-5 network cable into base and PoE switch or adapter to outlet not controlled by switch. For wall mount: Reverse wall mount clip, insert mounting bracket into wall plate, position eyelets against studs, slide down to lock.
For C4500 Handset: Install battery as in Preparations. Place on C4300 or main base for charging/registration. Automatic registration on first placement to compatible 2-line SIP base (e.g., S2410): MESSAGE WAITING LED flashes once, 3 rising beeps. Deregistration: When idle, press MENU > Deregister Handset > Select > OK. To register to another base, place on new base for automatic process. Ensure installation height under 2 meters.
CAUTIONS: Use only supplied cords; call 1-888-907-2007 for replacements. Risk of explosion with wrong battery type.
Place C4500 handset on C4300; CHARGE LED should turn on (full charge in 16 hours). For system check: Ensure network cable secure. Press LINE 1 or LINE 2 on handset for dial tone, then end call. Verify registration by placement (LED flashes, beeps). Test incoming call: Handset rings, MESSAGE WAITING LED flashes. For range, test within effective range; handset beeps if out. If no dial tone, unplug/replug network 15 seconds. In hospitality, test speed dials and conference.
Hospitality: Speed dial for services; energy-saving mode; 2-line operation.
Program via compatible base: Press recessed PROGRAM key. Speed dial: Up to 10 keys; press PROGRAM, select key, enter number (up to 32 digits). Flash duration: 3 options via PROGRAM. Voicemail detection: FSK and voltage methods via PROGRAM. Energy-saving: On idle handset, press *331734# then HOLD (3 beeps), place in charger. Battery replacement: Pry open cover, remove screw, unplug old, install new BT266342, secure. Changes effective upon confirmation.
Hospitality: Program speed dials for guest services; easy deregistration for room turnover.
Default settings indicated by asterisks (*). Adjustments via handset/base menu.
| Setting | Default | Options | Comments |
|---|---|---|---|
| Listening Volume | Medium (4*) | 1-8 | During call: VOLUME +/-; resets per call |
| Speakerphone Volume | Medium (4*) | 1-8 | During call: VOLUME +/- |
| Ringer Volume | Medium (2*) | Off, Low, Medium, High | Idle: VOLUME +/- |
| Ringer Tone | Tone 1* | Tone 1,2,3 | MENU > Ringer Tone |
| RF Transmission Power | Middle (2*) | Low (1), Middle (2), High (3) | For range adjustment; coverage varies |
| Flash Duration | 600ms (3*) | 100ms (1), 300ms (2), 600ms (3) | MENU > Flash |
Admin Access: Menu-driven for adjustments; voicemail settings, speed dial, SIP configurations.
| Symptom | Possible Cause | Corrective Action |
|---|---|---|
| Handset does not ring | Ringer off; not registered. | Adjust ringer VOLUME; re-register handset to base. |
| Handset does not work | Low battery; out of range. | Charge 16 hours; move closer to base; check registration. |
| CHARGE LED off | Misalignment; power issue. | Reposition; check adapter; unplug/replug 15s. |
| No dial tone on LINE 1/2 | Base connection; range. | Verify base power/line; move closer; re-register. |
| Poor audio/Interference | Distance; environmental. | Reduce distance; adjust RF power; avoid interference sources. |
| Low battery | Depleted; old battery. | Charge 16 hours; replace with BT266342 if needed. |
Care: Wipe with soft damp cloth; avoid liquids. Dispose battery properly via RBRC®. For service: www.vtechhotelphones.com or 1-888-907-2007.