The VTech C4011-USB is a 2-Line Accessory Cordless Handset Charging Stand with USB Charging Port, designed for use with VTech Analog Contemporary Series 2-line cordless handsets, such as the CTM-C4201. It provides charging functionality for accessory handsets and includes a USB port for charging external devices (up to 1A @ 5.1V). It can be used in desktop configurations and is part of a system that includes the CTM-A2421-BATT telephone base with power adapter. Below are the key specifications, installation, operation, programming, and troubleshooting instructions.
Verify all parts are included: Cordless Charging Stand with USB Charging Port (C4011-USB), power adapter, power cord. Install and charge handset battery before use. Ensure handsets are registered to compatible 2-line base before placing into C4011-USB for charging. Keep handset in the telephone base or charging stand when not in use for optimal performance. Avoid placing near communication devices, heat sources, noise sources, dust, moisture, low temperatures, or mechanical vibrations.
WARNING! This product should be installed by a qualified technician. Save these instructions.
The C4011-USB is an Analog cordless 2-line charging stand with USB charging port designed for use with VTech Analog Contemporary Series cordless handsets. It includes charge LED, charging poles, USB port (side-mounted for external device charging up to 1A @ 5.1V), and a base for desktop use. Supports battery charging and automatic handset registration/deregistration for up to 2 lines. Unique hospitality features: Integration with speed dial keys (e.g., CONCIERGE, FRONT DESK) for quick service access, message waiting LED (steady/periodic high/low voltage pulse, reverse polarity, FSK, Siemens/Panasonic). Nominal effective range varies by environment; crystal-controlled PLL synthesizer with channels, transmit frequency, max power less than 21dBm (126mW). Designed for guest room cordless mobility in 2-line setups with USB charging convenience.
Applications: Hospitality analog telephony; cordless 2-line charging stand with USB for hotel desk setups.
CAUTION! To prevent electrical shock or equipment damage, unplug before installation. Use only supplied power adapter.
WARNING! Follow safety precautions to reduce risk of fire, electric shock, or injury. Do not use near water; avoid rough handling. Do not open casing. Maintain 6-inch distance from medical devices. Wiring conforms to local codes. Avoid storms or gas leaks. Install by qualified technician only; connect only to host equipment. Use only specified adapter (Input: 100-240V AC 50/60 Hz, Output: 6V DC @ 1.5 A) and battery (Ni-MH AAA 550 mAh 2.4 V); incorrect types risk explosion. Dispose batteries per local codes, not in fire. Keep metallic objects away from handset. Mount at less than 2 meters height. For Analog: Avoid interference from other devices; operate in appropriate ambient conditions.
Plug the power adapter into the electrical outlet (not controlled by a switch) and connect the power cord to the charging stand. Place the compatible cordless handset on the charging poles; the charge LED illuminates during charging (full charge in 16 hours). For cordless integration, register the handset to a compatible 2-line telephone base by placing it in the cradle—automatic registration occurs with confirmation. Deregistration: On idle handset, press *331734# then HOLD for confirmation tone. To register to another base, place on new base for automatic process. Desktop: Place on flat surface. Ensure installation height under 2 meters. Use USB port for charging external devices only.
Place handset on C4011-USB; charge LED should turn on. For full system check with compatible 2-line base: Ensure power and telephone line cords are secure. Press LINE 1 or LINE 2 on handset for dial tone, then OFF to hang up. Verify registration by placing handset on base (confirmation). Test incoming call: Handset rings, message waiting LED flashes on base/handset. For cordless range, move handset within effective range and confirm no interference. Adjust RF transmission power if out of range. If no dial tone, unplug/replug power for 15 seconds to synchronize (up to 1 minute). In hospitality, test speed dial keys (e.g., CONCIERGE) for programmed numbers and USB charging for devices.
USB: Side port for charging devices (up to 1A @ 5.1V).
Program speed dial on compatible base/handset: Up to 11 keys (32 digits each). Deregistration: Idle handset, press *331734# then HOLD. No direct programming on C4011-USB; relies on handset/base. For hospitality, program speed dials for services. Battery replacement: For paired handset, open cover, unplug old, install new Ni-MH AAA550*2, secure. Changes effective immediately upon confirmation tone.
Default settings indicated by asterisks (*). Adjustments via base keys.
| Setting | Default | Options | Comments |
|---|---|---|---|
| Listening Volume | 4* | 1-6 | During call: VOLUME +/-; resets per call |
| Speakerphone Volume | 4* | 1-6 | During call: VOLUME +/- |
| Ringer Volume | 2* | 1-3 | Idle: Adjust on base |
| Ringer Tone | Tone 1* | Tone 1-3 | PROGRAM, 00, select |
| RF Transmission Power | Middle (2*) | Low (1), Middle (2), High (3) | PROGRAM, 01, select |
| Flash Duration | 600ms (3*) | 100ms (1), 300ms (2), 600ms (3) | PROGRAM, FLASH, select |
Admin Access: Recessed PROGRAM key for adjustments, including voicemail detection.
| Symptom | Possible Cause | Corrective Action |
|---|---|---|
| CHARGE LED off | Handset misaligned; dirty contacts. | Reposition handset; clean contacts with eraser/dry cloth; unplug/replug adapter 15s. |
| Battery issues | Low/depleted battery. | Charge 16 hours; if needed, charge 30 min min; replace with specified battery. |
| No dial tone on LINE 1/2 | Power/line issue. | Unplug/replug power 15s; test with working phone; contact provider. |
| Cannot dial out | Noise/no dial tone. | Ensure quiet; confirm dial tone; contact provider if hotel-wide. |
| No ring | Out of range; low volume. | Move closer to base; adjust ringer VOLUME; check interference. |
| Interference/fading | Distance; HSIA/modems. | Reduce distance; install DSL filter; relocate from appliances. |
| USB not charging device | Overload or incompatible device. | Ensure device draws up to 1A; check connections; use for charging only. |
Care: Wipe with soft damp cloth; avoid liquids. Dispose battery properly.