The VTech 6051 is a DECT 6.0 cordless telephone system with caller ID, voicemail indicator, and expandable design (up to 5 handsets, includes 3 handsets). It features a backlit display, speakerphone, phonebook (50 entries), call log (50 entries), redial (10 entries), adjustable ringer, and intercom. Supports English. Below are the key specifications, installation, operation, programming, and troubleshooting instructions.
Unpack the phone and ensure all components are present: telephone base, 3 cordless handsets, 3 rechargeable battery packs (2.4V 400mAh Ni-MH), 3 belt clips, base power adapter (6V DC), telephone line cord, 2 chargers, desk/table bracket, user's manual. Install batteries in handsets and charge for 16 hours before first use. Place base away from water, heat sources, and interference. Use desk bracket for tabletop setup.
WARNING! Failure to read and follow all instructions carefully before installing or operating this control could cause personal injury and/or property damage. Save these instructions.
The VTech 6051 is a cordless DECT 6.0 phone with voicemail indicator (network-based). Features include backlit display, speakerphone, adjustable ringer, 50-name phonebook, 50-name caller ID log, 10-number redial, intercom, conference calling, voicemail waiting indicator. Handset and base layouts include navigation keys, volume controls, dedicated buttons for mute, redial, find handset, INT.
Applications: Residential cordless telephony; Compatible with DSL/Caller ID; Up to 5 handsets, starts with 3.
CAUTION! To prevent electrical shock/equipment damage, unplug before installation. Use only supplied adapters. If in doubt about wiring, consult qualified electrician.
WARNING! Do not use on circuits exceeding 120 VAC; improper use can cause shock/fire. All wiring must conform to local/national electrical codes. Avoid use during storms, near gas leaks, or with pacemakers without consulting doctor (maintain 6-inch distance). Dispose of batteries per local regulations. Install DSL filter if using high-speed internet. Risk of electric shock: Do not disassemble. Avoid water; handle with dry hands.
Shut off power if applicable. Remove old phone cover. Label wires before disconnecting. Disconnect wires one at a time; do not let fall into wall. Remove old base from wall.
Plug telephone line cord into base and wall jack (use DSL filter if needed). Plug power adapter into base and unswitched outlet. Install batteries in handsets (observe polarity, close cover). Place handsets in base/chargers to charge for 16 hours. For desk setup, use pre-installed bracket. Register additional handsets via menu. Set dial type if using pulse service.
Terminal Designations: RJ11 jack for line cord on base; DC jack for power adapter.
Standard Setup: Wall jack to DSL filter (if needed) to base RJ11; Power outlet to adapter to base DC jack.
Desk Mount: Bracket pre-installed.
CAUTION! All wiring must conform to local/national electrical codes. Do not use switched outlets.
After charging, lift handset and listen for dial tone. Test by dialing a number and adjusting volume. Verify CHARGE light on base. Test find handset feature.
View via CID; new calls with icon. Dial back with /FLASH. Save to phonebook via SELECT. Up to 50 entries.
Access menu with MENU/SELECT. Set date/time, program phonebook, configure ringer.
Enter menu via MENU/SELECT. Adjust ringer volume/melody, key tone, out of range tone, dial type, handset name, clear voicemail.
| Setting | Default | Options | Comments |
|---|---|---|---|
| Ringer Volume | Level 3 | 1-5/Off | Handset ringer |
| Ringer Melody | Melody 1 | 1-5 | Select ring pattern |
| Key Tone | On | On/Off | Beep on key press |
| Out of Range Tone | On | On/Off | Alert when out of range |
| Dial Type | Tone | Tone/Pulse | For rotary service |
| Handset Name | HANDSET | Custom (up to 11 chars) | Personalize display |
| Clear Voicemail | N/A | Execute | Turn off indicator |
| Symptom | Possible Cause | Corrective Action |
|---|---|---|
| Telephone does not work at all | Power off, low battery. | Check power adapter, charge battery; ensure base installed properly. |
| Display shows "No line" or no dial tone | Wiring issue, service problem. | Test line cord on another phone; contact provider; install DSL filter. |
| Handset not registered | Not registered. | Place in base to auto-register (60 sec). |
| Handset does not ring | Ringer off, volume low. | Set ringer via menu; check connections. |
| Poor audio quality | Interference, out of range. | Move away from electronics; charge battery. |
| Cannot dial out | Wrong dial type. | Set to pulse if needed. |
| No caller ID | Service not subscribed. | Subscribe to service; install DSL filter. |