The VTech 18050 is a cordless telephone system with digital answering machine, caller ID, and expandable design (up to 5 handsets). It features a backlit display, speakerphone, phonebook (50 entries), call log (30 entries), redial (5 entries), call block (20 entries), quiet mode, voicemail indicator, and volume boost. Supports English. Below are the key specifications, installation, operation, programming, and troubleshooting instructions.
Unpack the phone and ensure all components are present: telephone base, 2 cordless handsets, 2 chargers, 2 rechargeable batteries, battery covers, base power adapter (100-240V AC 50/60Hz to 6V DC @ 450mA), 2 charger power adapters (to 6V DC @ 400mA), telephone line cord, user's manual. Install batteries in handsets (align contacts, snap cover) and charge for 16 hours before first use. Place base away from water, heat sources, and interference. Use wall mount if desired.
WARNING! Failure to read and follow all instructions carefully before installing or operating this control could cause personal injury and/or property damage. Save these instructions.
The VTech 18050 is a cordless DECT phone with digital answering system (up to 99 messages). Features include backlit display, speakerphone, adjustable ringer (10 melodies), 50-name phonebook, caller ID log, 5-number redial, call block, quiet mode, voicemail waiting indicator, call screening, remote access, volume boost, alarm clock. Supports English. Handset and base layouts include navigation keys, volume controls, dedicated buttons for mute, redial, find handset, INT.
Applications: Residential cordless telephony; Compatible with DSL/Caller ID; Up to 5 handsets.
CAUTION! To prevent electrical shock/equipment damage, unplug before installation. Use only supplied adapters. If in doubt about wiring, consult qualified electrician.
WARNING! Do not use on circuits exceeding 100-240 VAC; improper use can cause shock/fire. All wiring must conform to local/national electrical codes. Avoid use during storms, near gas leaks, or with pacemakers without consulting doctor. Dispose of batteries per local regulations. Install DSL filter if using high-speed internet. Use only specified adapters and batteries.
Shut off power if applicable. Remove old phone cover. Label wires before disconnecting. Disconnect wires one at a time; do not let fall into wall. Remove old base from wall.
Plug telephone line cord into base and wall jack (use DSL filter if needed). Plug power adapter into base and unswitched outlet. Install batteries in handsets (align contacts). Place handsets in base/chargers to charge for 16 hours. For wall mount, slide base onto plate. Register additional handsets via FIND HANDSET on base (hold 6s).
Terminal Designations: RJ11 jack for line cord on base; DC jack for power adapter.
Standard Setup: Wall jack to DSL filter (if needed) to base RJ11; Power outlet to adapter to base DC jack.
Wall Mount: Route cords through slots.
CAUTION! All wiring must conform to local/national electrical codes. Do not use switched outlets.
After charging, lift handset and listen for dial tone. Test by dialing a number and adjusting volume. Verify CHARGE light on base. Test paging: Press FIND HANDSET on base.
View via /VOL-; new calls with icon. Dial back with TALK/FLASH. Save to phonebook via OK/MENU > SAVE.
Access menu with OK/MENU. Set date/time, program phonebook, configure ringer.
Enter menu via OK/MENU. Adjust LCD language, key tone, ringer volume/tone, voicemail number, call block, quiet mode.
| Setting | Default | Options | Menu Path |
|---|---|---|---|
| LCD Language | English | English | HS SETTINGS > LCD language |
| Key Tone | On | On/Off | HS SETTINGS > TONE SETUP > Key tone |
| Ringer Volume | Level 3 | 1-6/Off | HS SETTINGS > RING SETUP > Volume |
| Ringer Tone | Tone 1 | 1-10 | HS SETTINGS > RING SETUP > Melody |
| Voicemail Number | None | Custom | Service provider |
| Call Block | Off | On/Off, up to 20 entries | CALL BLOCK > Add entry |
| Quiet Mode | Off | On/Off | Set ringer to off |
| ECO Mode | Off | On/Off | BS SETTINGS > ECO mode |
| Symptom | Possible Cause | Corrective Action |
|---|---|---|
| Telephone doesn’t work at all | Power cord not plugged; battery not connected. | Plug power cord securely; reconnect battery. |
| No dial tone | Line cord defective. | Connect to different jack/phone; contact provider. |
| Poor audio quality | Interference from appliances; out of range. | Move closer to base; avoid electronics. |
| Handset not performing normally | Power cord loose; out of range. | Plug power securely; move closer. |
| Handset battery not charging | Charger light off; faulty cord/outlet. | Check connections; try different outlet. |
| Telephone does not ring | Ringer off; cords loose. | Turn ringer on; secure cords. |
| Calls disconnect prematurely | Base unplugged; interference. | Keep base plugged; move away from interference. |
| No Caller ID | Not subscribed. | Subscribe to service. |
| Answering machine not answering | Off; full. | Turn on; delete messages. |
| Time and day not set | Date/time not set. | Set via menu. |